NetComm NB604N DSL Wireless Router

Shortcuts

	NetComm NB604N
details:	ADSL2+ Wireless N300 Modem Router
hardware type:	DSL Wireless Router
date added:	2012-07-10
updated:	2013-04-15

The NetComm NB604N ADSL2+ wireless N300 router allows you to connect to a broadband Internet service and share the connection with multiple users.

With a built-in Wireless N access point providing speeds of up to 300Mbps, multiple users are able to connect any Internet enabled device to the NB604N wirelessly. The NB604N includes a built-in 4 port Ethernet switch, allowing for other devices to access the Internet over a wired connection as well.

The NB604N offers IPv6 support, the latest generation of Internet addressing. This means the NB604N is future proofed against the upcoming exhaustion of the IPv4 address space.

The NetComm NB604N ADSL2+ wireless N300 router features a WPS push button that allows for an easy set-up of your wireless network, a push button to easily turn your wireless signal on and off, advanced security options to ensure your network remains safe and an easy to navigate web interface if you need to change any settings.

All NetComm products

All DSL Wireless Routers

NB604N Features
General
Availability:	currently available
LAN / WAN Connectivity
WAN ports:	1
WAN port(s) type:	DSL/ISDN/POTS connector (RJ-11)
LAN ports:	4
LAN ports type:	10/100 Base-TX (RJ-45)
LAN ports auto cross-over:
USB port(s):	1 for storage devices
USB port type:	USB 2.0
Router
NAT routing:
Multihomed:
DMZ:
Port forwarding:
DHCP server:
DHCP client:
Dynamic DNS client:
QoS:
UPnP:
Transparent Bridging (IEEE 802.1d):
Routing Protocols:	RIP v1 (static routing, RFC 1058) RIP v2 (dynamic routing, RFC1389)
DSL
DSL compliance:	ADSL1 (G.dmt 992.1, G.lite 992.2, G.hs 994.1, DMT T1.413) ADSL2 (G.992.3, G.lite.bis 992.4) RE-ADSL2 (G.992.3 Annex L) ADSL2+ (G.992.5)
PPPoE client:
PPPoA client:
Wireless
Maximum Wireless Speed:	300 Mbps (Wi-Fi 4)
WiFi standards supported:	802.11b (Wi-Fi 1) 802.11g (Wi-Fi 3) 802.11n (draft 2.0)
Wifi security/authentication:	WEP WPA (TKIP) WPA2 (AES) 802.1X (EAP-MD5/TLS/TTLS/PEAP)
WiFi modes:	Access point Repeater mode
external antenna(s):	2
ext antenna(s) removable ?:
Antenna gain:	2 dBi
Multiple SSID:
WDS compatible:
WMM (QoS):
WPS (Wi-Fi Protected Setup):
VPN
	IPSec
IPSec passthrough:
Device Management
Default IP address:	192.168.1.1
Default admin username:	admin
Default admin password:	admin
Administration:	Web-based (LAN) TFTP (RFC 1350)
Firmware upgradeable:
Configuration backup/restore:
Event log:
Usage Statistics:
Diagnostic functions:
Misc hardware info
IPv6 support:
NTP client:
Links
Product page:	http://www.netcommwireless.com/product/x...
Manual:	http://media.netcomm.com.au/public/asset...
Quick Install Guide:	http://media.netcomm.com.au/public/asset...

Please use the Add Comment function below to review devices you have used (please be descriptive). If you find an error in our database, or have additional information about the product, please

User Reviews/Comments:

rate: avg:

by fubar - 2012-12-17 17:05

Relatively old these days but that's what the ISP (tpg in Australia) recommend - probably the least heat generation of any ADSL2+ modem I've used - much cooler than my old billion 7401vgm (now that's a POS) and the Dynalink so with any luck might last a while. Wireless coverage is good enough.

I'm getting close to the max throughput for local speedtest at about half a mile from the exchange.

Good enough and relatively cheap if you don't need voip built in - I use a gigaset so this is fine.