Your P4 Temps

Joel · Post by **Joel** » Wed May 19, 2004 12:27 am

Post'em. Trying to find out what's good and what's bad.

List what HSyou're using, Fan, Thermal coumpound, idle temps an full load.

Cypher · Post by **Cypher** » Wed May 19, 2004 12:56 am

Do I count?
I never idle because I fold <hint>

TIM= AS5
I'm at 26C full load 24/7 on a hot day.

God I love my Cascade. Hand built by the God of water cooling himself. :2cool:

Brk · Post by **Brk** » Wed May 19, 2004 10:46 am

3.0 GHz P4 with Thermalright SLK-900, 80mm Panaflo low and AS3Around 38-40 C idle, upwards of 60 at load.

But I don't pay attention to temps anymore. I don't overclock anymore either. I just use the PC

TrevGlas · Post by **TrevGlas** » Wed May 19, 2004 12:45 pm

Spark 7 HSF, p4 2.8 Oc'ed to 3.2, Specs in Sig

Temps were higher a little bit ago because I was putting too much AS5 on.. now I have the perfect amount. This is also after running EQ for a few hours.. idles a little bit lower.

Idles at about 27,28.. with a room temp of 80

At full RPM (6500) idles at 24-25

TrevGlas · Post by **TrevGlas** » Wed May 19, 2004 12:51 pm

Here is full load for a few minutes....doesnt really get any higher.. maybe a degree or 2.. using Arctic Silver 5

sentra8777 · Post by **sentra8777** » Wed May 19, 2004 4:17 pm

right now have my air running iam at 34 c idel.

Chris · Post by **Chris** » Wed May 19, 2004 6:58 pm

2.4c 100% load 24/7, hyperthreading enabled, two instances of FAH
TT Volcano 7 plus on mid speed 39 celcius

Mark · Post by **Mark** » Wed May 19, 2004 7:22 pm

folding as always, room at 80F

Jeremy · Post by **Jeremy** » Wed May 19, 2004 7:23 pm

older 1.8a with stock cooling is 40 idle, 47-49 full with AS5 which i don't know if it's applied well or not. fan usually 2400rpm idle, 3000rpm full. the cpu fan is also the only fan in my case apart from the psu which makes temps higher but it is very quiet.

Jeremy

Mark · Post by **Mark** » Thu May 20, 2004 6:20 pm

no one noticed my v-core settings ?, ha ha ha

Joel · Post by **Joel** » Thu May 20, 2004 7:35 pm

My bro's 'puter runs about 42C idle and I'm not sure what full load...It's got the stock P4 fan with Cerimaque on it. Problem might be that he used it for a while with the thermal pad on and then put some older AS on, then put this stuff on, so it migh have kind of messed up the results he'll get.

It's a 2.8C, so.

TrevGlas · Post by **TrevGlas** » Thu May 20, 2004 8:17 pm

Too thick of an application can REALLY mess up your temps... I had too much on and my cpu was hitting the threshold and rebooting

follow tehse instructions
http://www.arcticsilver.com/arctic_silv ... ctions.htm

Start at #10

TrevGlas · Post by **TrevGlas** » Thu May 20, 2004 8:18 pm

Completely clean off all the old applications with 90% + rubbing alcohol, then follow those instructions

YARDofSTUF · Post by **YARDofSTUF** » Thu May 20, 2004 8:42 pm

my temps are 50is at 1.675 volts.

lance-tek · Post by **lance-tek** » Thu May 20, 2004 10:26 pm

3.0 @ 3.5 Temps are 60.5 C at 1.6

It is HT and has 100% usage cause I am folding 24/7

-lance

Cypher · Post by **Cypher** » Thu May 20, 2004 11:29 pm

lance-tek wrote:3.0 @ 3.5 Temps are 60.5 C at 1.6

It is HT and has 100% usage cause I am folding 24/7
**Dam I wish I was water cooling**
-lance