help to network XPpro to win98se

Networking, Wireless Routers (802.11 a/b/g/n/ac/ax WiFi), NAT, LAN configuration, equipment, cabling, hubs, switches, and general network discussion
Post Reply
User avatar
CBR900RR
Regular Member
Posts: 109
Joined: Sat Jul 01, 2000 12:00 am
Location: Honolulu, HI, USA

help to network XPpro to win98se

Post by CBR900RR »

I did sucess networking COMP1 running XPpro (NTFS, 3com NIC) to COMP2 running 98se (FAT32, netgear 10/100 NIC) using a linksys 4 port router, both comp's internal IP is manually assign(DHCP disable), overall thru put is acceptable, 7.5MB/s, problem is everytime I click a folder or save something from comp1 to comp2, sometime takes up to 10 sec for the folder to start opening or the file to start saving.

It work fine before when comp 1 is running winME, but when I did a clean install XP, I can choose which protocol to use, but cannot bind netbeui for internal networking and TCP/IP for the internet, the binding option is not there. Don't know which protocol I am networking right now because the option is not there.


Comp 1 is my main comp and not sharing anything. Pic below

Image

Image

Comp 2 is an old Dell 133mhz which I install a second HD for use as a network HD for files and mp3 storage. I did enable NETBEUI on comp2 to bind with file and print sharing for internal networking and TCP/IP for the internet, both NIC is 100mb full dulplex.

Seems like the 2 comp are using a different protocol, but somehow network together, thanks for reading the long post.
Samsung 760v TFT @ 1280 X 1024 32 bit
Lian-Li PC67 with 2 80mm U1A / 2 HD cooler intake and 1 80mm H1A / 1 80mm ADDA exhaust
NF7-S v2.0 (BIOS 18) (SATA 10033) (nforce pack 2.45) AS2 on NB Heat sink on SB
Alpha PAL 8045 with Thermaltake Smart Fan (blowing away from HS)
XP2500+ Barton/AQXEA (9) 0323/11X200/AS2/Vcore 1.725/DDR 2.6/Chipset 1.7/Agp 1.5/Idle 36/Load 51
Mushkin blk lvlII DDR3200 2X256MB 11-2-2-2 DC
IDE 1 master Plextor CDRW 24X
IDE 2 master Sony DRU510A DVD+/- r/rw CDRW
Sata Raid 2X IBM 60GB GXP60
Sony Floppy
ATI Radeon 8500 128MB DDR (retail) Infineon 3.6ns @ 275/275 BlueORB/RamSink CATALYST™ 3.6
PCI 3 ATA 100 PCI card WD SE 80GB/Zip100
5X round ide cable
Sparkle 400w with 1 80mm U1A fan
On cable modem and Dlink DI-614+ router with speed patch
Windows XP pro (NTFS)(SP1)

3Dmark2001se 12300
User avatar
BlackSword
Advanced Member
Posts: 700
Joined: Thu Apr 19, 2001 12:00 am
Location: Ontario, Canada

Post by BlackSword »

This sounds familiar,,, except it was Win2000 and 98se I think,, I am pretty sure YeOldStoneCat was in the Thread, you could try searching his name to see if something pops up.

I will hopefully have my new Rig with XP this week, I will be putting it in my lan that has a ME rig and a 98se rig. So if nothing comes up for you by then I will see how I make out and repost.
P4 2.4ghz 512ram XP pro ATI 9600pro
P4 2.0ghz 256ram Win2000 Geforce2 MX 400
P4 1.6ghz 512ram XP Home Geforce4 Ti4200
P3 866mhz 320ram ME & XP pro TNT2
All thru HotBrick 600
P3 1.1ghz 260ram Win2000 laptop
User avatar
CBR900RR
Regular Member
Posts: 109
Joined: Sat Jul 01, 2000 12:00 am
Location: Honolulu, HI, USA

Post by CBR900RR »

Thanks, I will check it out.
Samsung 760v TFT @ 1280 X 1024 32 bit
Lian-Li PC67 with 2 80mm U1A / 2 HD cooler intake and 1 80mm H1A / 1 80mm ADDA exhaust
NF7-S v2.0 (BIOS 18) (SATA 10033) (nforce pack 2.45) AS2 on NB Heat sink on SB
Alpha PAL 8045 with Thermaltake Smart Fan (blowing away from HS)
XP2500+ Barton/AQXEA (9) 0323/11X200/AS2/Vcore 1.725/DDR 2.6/Chipset 1.7/Agp 1.5/Idle 36/Load 51
Mushkin blk lvlII DDR3200 2X256MB 11-2-2-2 DC
IDE 1 master Plextor CDRW 24X
IDE 2 master Sony DRU510A DVD+/- r/rw CDRW
Sata Raid 2X IBM 60GB GXP60
Sony Floppy
ATI Radeon 8500 128MB DDR (retail) Infineon 3.6ns @ 275/275 BlueORB/RamSink CATALYST™ 3.6
PCI 3 ATA 100 PCI card WD SE 80GB/Zip100
5X round ide cable
Sparkle 400w with 1 80mm U1A fan
On cable modem and Dlink DI-614+ router with speed patch
Windows XP pro (NTFS)(SP1)

3Dmark2001se 12300
User avatar
BlackSword
Advanced Member
Posts: 700
Joined: Thu Apr 19, 2001 12:00 am
Location: Ontario, Canada

Post by BlackSword »

CBR900RR,

any luck?

I just setup my new XP box last night,, didn't have much time but for starters my ME box sees the XP box and the TWO 98se boxes but the 98se boxes don't see XP and the XP box doesn't see the 98se boxes.

As far as XP to ME it is like the hard-drives are local to each other, very fast, appears to be little to no delay.

AND YES, isn't it a pain having to figure out where everything is.... totally different from 98se, ME & NT4.

Lucky I like change! ;)
P4 2.4ghz 512ram XP pro ATI 9600pro
P4 2.0ghz 256ram Win2000 Geforce2 MX 400
P4 1.6ghz 512ram XP Home Geforce4 Ti4200
P3 866mhz 320ram ME & XP pro TNT2
All thru HotBrick 600
P3 1.1ghz 260ram Win2000 laptop
User avatar
CBR900RR
Regular Member
Posts: 109
Joined: Sat Jul 01, 2000 12:00 am
Location: Honolulu, HI, USA

Post by CBR900RR »

Browseing on the file folder is fast except on the pic folder, about 450MB in size, maybe XP want to cashe all the pic in my folder for preview???? As far as the speed go, both comp are 100mb full dulplex and I am getting 1.96 megabyte or 15.68 megabit per second. Still searching for info to speed up my networking speed.
Samsung 760v TFT @ 1280 X 1024 32 bit
Lian-Li PC67 with 2 80mm U1A / 2 HD cooler intake and 1 80mm H1A / 1 80mm ADDA exhaust
NF7-S v2.0 (BIOS 18) (SATA 10033) (nforce pack 2.45) AS2 on NB Heat sink on SB
Alpha PAL 8045 with Thermaltake Smart Fan (blowing away from HS)
XP2500+ Barton/AQXEA (9) 0323/11X200/AS2/Vcore 1.725/DDR 2.6/Chipset 1.7/Agp 1.5/Idle 36/Load 51
Mushkin blk lvlII DDR3200 2X256MB 11-2-2-2 DC
IDE 1 master Plextor CDRW 24X
IDE 2 master Sony DRU510A DVD+/- r/rw CDRW
Sata Raid 2X IBM 60GB GXP60
Sony Floppy
ATI Radeon 8500 128MB DDR (retail) Infineon 3.6ns @ 275/275 BlueORB/RamSink CATALYST™ 3.6
PCI 3 ATA 100 PCI card WD SE 80GB/Zip100
5X round ide cable
Sparkle 400w with 1 80mm U1A fan
On cable modem and Dlink DI-614+ router with speed patch
Windows XP pro (NTFS)(SP1)

3Dmark2001se 12300
Post Reply