" Nat error "Azureus (no firewall and no share internet connection)

windjaz · Post by **windjaz** » Sun Dec 11, 2005 1:50 pm

I still have NAT error. I'm set up to allow TCP - what now???

Izzo · Post by **Izzo** » Sun Dec 11, 2005 2:06 pm

windjaz wrote:I still have NAT error. I'm set up to allow TCP - what now???

start>run>cmd>enter

type: ipconfig (to find ip address)
take IP add and plug that into the field inside the CP of your router.

windjaz · Post by **windjaz** » Sun Dec 11, 2005 2:20 pm

Izzo wrote:start>run>cmd>enter

type: ipconfig (to find ip address)
take IP add and plug that into the field inside the CP of your router.

My router already has the IP address setup. The WIKI says something about needing to create a Static IP address?? I looked at the manual but I just don't get it. Is there something simpler to do??

Izzo · Post by **Izzo** » Sun Dec 11, 2005 2:23 pm

windjaz wrote:My router already has the IP address setup. The WIKI says something about needing to create a Static IP address?? I looked at the manual but I just don't get it. Is there something simpler to do??

that's about as simply as i can explain it .... I have no problems.

edit>> plug ip into something similar shown ...

Athnyha · Post by **Athnyha** » Thu Dec 29, 2005 3:21 pm

I have changed my ip address before, but it was on my laptop that still runs of windows 98. My os right now is 2000 and it seems much different. Also I am connected by wireless, so I have no 'local area connection'. My current ip is 192.168.0.3. Help Please!

Izzo · Post by **Izzo** » Thu Dec 29, 2005 7:16 pm

Athnyha wrote:I have changed my ip address before, but it was on my laptop that still runs of windows 98. My os right now is 2000 and it seems much different. Also I am connected by wireless, so I have no 'local area connection'. My current ip is 192.168.0.3. Help Please!

What's your question?

Athnyha · Post by **Athnyha** » Sat Dec 31, 2005 12:26 am

the question I had then was about how to change my ip address to one seen in a previous post. Between the time I posted and now I have figured out how to change my ip address. However, it has not done anything except boot me off the web. My question now is: how do I fix the NAT error? I've most of the previous posts, and its all techno-gibberish to me. Sorry for the trouble, and thankyou

delimare · Post by **delimare** » Mon Jan 02, 2006 10:59 am

I have a Toshiba 2500, no router, PC-Cillian by Trend Micro. I've followed numerous guides, hints, suggestions and I still get the yellow light and a NAT error. Does anyone happen to know how to get into a Toshiba 2500 like you would a router? I couldn't find any info on it and I'm not sure if I need to forward ports in this specific modem, or not... Thanks.

Izzo · Post by **Izzo** » Mon Jan 02, 2006 12:15 pm

Athnyha wrote:the question I had then was about how to change my ip address to one seen in a previous post. Between the time I posted and now I have figured out how to change my ip address. However, it has not done anything except boot me off the web. My question now is: how do I fix the NAT error? I've most of the previous posts, and its all techno-gibberish to me. Sorry for the trouble, and thankyou

You've got to configure your router to allow for the traffic ....I posted a pic a few posts up ...that's about the best i can explain it ... no trouble at all ...

start>run>cmd>ipconfig> take the ip and plug that into where i've shown it and you should be good to go.

Izzo · Post by **Izzo** » Mon Jan 02, 2006 12:18 pm

delimare wrote:I have a Toshiba 2500, no router, PC-Cillian by Trend Micro. I've followed numerous guides, hints, suggestions and I still get the yellow light and a NAT error. Does anyone happen to know how to get into a Toshiba 2500 like you would a router? I couldn't find any info on it and I'm not sure if I need to forward ports in this specific modem, or not... Thanks.

I'm not entirely sure .. but I assume then you're running a software firewall ?

try to allow the app inside the firewall or MS's security center(if running SP2)

delimare · Post by **delimare** » Mon Jan 02, 2006 12:50 pm

Izzo wrote:I'm not entirely sure .. but I assume then you're running a software firewall ?

try to allow the app inside the firewall or MS's security center(if running SP2)

I dug around within PC-Cillian a bit more and added the UTorrent program to the exception list and that seemed to do it. I forgot that option was there or I would have tried it earlier

Izzo · Post by **Izzo** » Mon Jan 02, 2006 1:41 pm

delimare wrote:I dug around within PC-Cillian a bit more and added the UTorrent program to the exception list and that seemed to do it. I forgot that option was there or I would have tried it earlier

Good luck and happy downloading .... stick around a while and have fun.

brdrdude991 · Post by **brdrdude991** » Wed Jan 04, 2006 7:22 pm

So i've read this forum like twice adn i have no idea what to do my IP adress is 192.168.0.3 and everyone says to go to the router to change it or something and i have no idea how to do that

Izzo · Post by **Izzo** » Wed Jan 04, 2006 9:45 pm

brdrdude991 wrote:So i've read this forum like twice adn i have no idea what to do my IP adress is 192.168.0.3 and everyone says to go to the router to change it or something and i have no idea how to do that

what kind of router do you have ?

brdrdude991 · Post by **brdrdude991** » Wed Jan 04, 2006 9:49 pm

i have a netgear wireless mr814v2 but im not connectign through the wireless

Izzo · Post by **Izzo** » Wed Jan 04, 2006 9:58 pm

brdrdude991 wrote:i have a netgear wireless mr814v2

ok ..in your manual you should have been given an IP address to manually configure your router ..look for it and enter it in to your web browser

for example 192.168.1.1 (linksys)

then go to start>run>cmd then hit enter a DOS window will open ....at the prompt type in ipconfig

youll see ip address 192.x.x.x (x=whatever yours is) subnet mask 255.x.x.x(x=whatever yours is) and default gateway 192.x.x.x(x=whatever yours is)

take note of the IP address ...then go back to your router page and look for something like Applications and Gaming or port forwarding.. )should look something like teh pic i posted above ... enter the port for whatever torrent you need (azureas uses 6881 among others) enter that in similar to above ...make sure the protocol is TCP and then where you see the IP address enter the IP you made note of and then save changes ...

let me know

brdrdude991 · Post by **brdrdude991** » Wed Jan 04, 2006 10:05 pm

ya i got all the ip adress stuff just when you say router page i have no idea where that is
by the way thanks for all the help with eveyrone man. i just haven't reaqlly done much of this routing stuff before.

brdrdude991 · Post by **brdrdude991** » Wed Jan 04, 2006 10:07 pm

o man srry i just found it i was trying to use my ip adress to get to it but i had to use my default one i got it now thxx man

Izzo · Post by **Izzo** » Wed Jan 04, 2006 10:09 pm

brdrdude991 wrote:ya i got all the ip adress stuff just when you say router page i have no idea where that is
by the way thanks for all the help with eveyrone man. i just haven't reaqlly done much of this routing stuff before.

not a problem ..did you find the ip addy for your router ?

you enter it into a web browser like you would any other web address ...instead of http://www.something.com you enter the IP address for the router ..(a numerical address)

gimme a minute more ill find it

Izzo · Post by **Izzo** » Wed Jan 04, 2006 10:11 pm

Look Here

brdrdude991 · Post by **brdrdude991** » Wed Jan 04, 2006 10:11 pm

ya i typed it in but i im on the third cable slot so i was typinign in 192.618.0.3 when i needed to tyoe .0.1 so i got it now

Izzo · Post by **Izzo** » Wed Jan 04, 2006 10:14 pm

brdrdude991 wrote:ya i typed it in but i im on the third cable slot so i was typinign in 192.618.0.3 when i needed to tyoe .0.1 so i got it now

let me know how it works out

Izzo · Post by **Izzo** » Wed Jan 04, 2006 10:50 pm

ooookay then.

Izzo · Post by **Izzo** » Thu Jan 05, 2006 9:32 am

No more help for noobs

Whtny42 · Post by **Whtny42** » Fri Jan 27, 2006 1:37 am

I've also been having this little problem. I really am sorry if I sound like a noob (Who am i kidding, i am), but i have never done this kind of stuff before, so i feel overly cautious. After ransacking my bellsouth modem's site configuration thingy and finding the page to forward ports, I've come upon a Window that asks for the global port range and the base host port. I'm not sure what to enter for the base host port.

As for global range, i changed the defaulted port in azureas to 16881 per the advice of another guide (It spoke of certain isps throttling the downloading of the 6881 port, and just suggested you make a change regardless). How would this change my global port range thingy?

I also can only select between UDP and TCP. I read a few pages back that you should select TCP, but I notice all the port numbers in azureaus are coupled with a UDP, will this make any difference? I'm very sorry for the n00b infringement.

If someone has a moment, can you sum up the basics of port forwarding? I don't really understand it, and i'd like to have a basic idea of what im fooling with, if just for the future.

Thanks much.

Whtny42 · Post by **Whtny42** » Fri Jan 27, 2006 1:39 am

and i just realised that i bumped a very old thread...im sorry if there are rules against this, i should have checked the date. >_<

Izzo · Post by **Izzo** » Fri Jan 27, 2006 10:55 am

Whtny42 wrote:and i just realised that i bumped a very old thread...im sorry if there are rules against this, i should have checked the date. >_<

http://en.wikipedia.org/wiki/Port_forwarding

TCP and 6881 still work for me ...

Whtny42 · Post by **Whtny42** » Fri Jan 27, 2006 3:50 pm

ah, i should have thought of wiki.

I still dunno what i should put for the host port though. =/
again, any help is appreciated

Izzo · Post by **Izzo** » Fri Jan 27, 2006 4:13 pm

Whtny42 wrote:ah, i should have thought of wiki.

I still dunno what i should put for the host port though. =/
again, any help is appreciated

same port for both

Whtny42 · Post by **Whtny42** » Sat Jan 28, 2006 11:22 am

woot it works.

Much thanks for the help!

Izzo · Post by **Izzo** » Sat Jan 28, 2006 2:05 pm

Whtny42 wrote:woot it works.

Much thanks for the help!

cccallahan · Post by **cccallahan** » Tue Jan 31, 2006 7:04 am

Hello, i tried my hardest not to ask for help, just because I figured you'd be getting a bit irate about it now. But I can't help it, it's bugging me so much!

I'm on 2.2meg and i'm only reaching torrent speeds of 10kbps, and thats at the highest!
I'm using Azareus for Mac OS X and on testing port 6881 I recieve Nat Error.
I use OVISLINK router, and my port forwarding details are

http://img84.imageshack.us/img84/8690/picture23pe.jpg

To be honest i'm not 100% sure if that's my IP, because I can't seem to find it anywhere. Thats the IP it says in system preferences though.

Thankyou!

Izzo · Post by **Izzo** » Tue Jan 31, 2006 9:23 am

cccallahan wrote:Hello, i tried my hardest not to ask for help, just because I figured you'd be getting a bit irate about it now. But I can't help it, it's bugging me so much!

I'm on 2.2meg and i'm only reaching torrent speeds of 10kbps, and thats at the highest!
I'm using Azareus for Mac OS X and on testing port 6881 I recieve Nat Error.
I use OVISLINK router, and my port forwarding details are

http://img84.imageshack.us/img84/8690/picture23pe.jpg

To be honest i'm not 100% sure if that's my IP, because I can't seem to find it anywhere. Thats the IP it says in system preferences though.

Thankyou!

Mac Huh?...hmm I assume it works in similar fashion then ... try listing all your ports to 6881

I also assume there is a command similar to 'ipconfig' for windows that you give you your IP,Gateway and Subnet mask...I'm clueless about MAC's but it appears you everything needed but just need to fill in the blanks with the appropriate information....source and destination should be the same ports....other than that ...hmmm

oh...and no worries on the help...just kinda bugs when people get the help and then disappear ....again as i've posted before...stick around n stay a while

cccallahan · Post by **cccallahan** » Tue Jan 31, 2006 9:39 am

thanks, im going to give that a try in a bit.
at the moment im just using a normal modem, but when my brother comes back ill have to set the router up (eg he leaches off my internet!)

i will stick around

x

mmione · Post by **mmione** » Tue Jan 31, 2006 10:11 am

make sure your forward both TCP/UDP.

cccallahan · Post by **cccallahan** » Tue Jan 31, 2006 1:35 pm

one more question.
i'm on bt 2.2meg, using a speedtouch 330 ext. modem.
using azareus.

with a torrent from a public site like torrentspy.com i never seem to get the download going more than 20kbps, the upload goes about 30/35kbps, even with a well seeded torrent
( specifically, this file http://ts.searching.com/torrent/520331/ ... US_RELEASE )

is this what i should expect?

Izzo · Post by **Izzo** » Tue Jan 31, 2006 2:02 pm

cccallahan wrote:one more question.
i'm on bt 2.2meg, using a speedtouch 330 ext. modem.
using azareus.

with a torrent from a public site like torrentspy.com i never seem to get the download going more than 20kbps, the upload goes about 30/35kbps, even with a well seeded torrent
( specifically, this file http://ts.searching.com/torrent/520331/ ... US_RELEASE )

is this what i should expect?

Hard to say ... depending on seeds and so forth ... I cap my upload speed and max out the download.....just tweak whatever client you're using. If the seeds are there I get upwards of 300kbps +

cdogg · Post by **cdogg** » Tue Feb 07, 2006 9:09 pm

okay,im having problems with azureus and the nat error. im allowing port 6881 in my firewall but i still cant download with azureus or any other bittorrent client. i have an asante router but i cant figure out how to do port forwarding.

Edit: okay, ive figured out how to do port forwarding but its still not working. ive also heard they shut down ports from 6881 to 6999, im not sure if its true but i heard it on a website. please help!!

Izzo · Post by **Izzo** » Thu Feb 09, 2006 10:15 am

cdogg wrote:okay,im having problems with azureus and the nat error. im allowing port 6881 in my firewall but i still cant download with azureus or any other bittorrent client. i have an asante router but i cant figure out how to do port forwarding.

Edit: okay, ive figured out how to do port forwarding but its still not working. ive also heard they shut down ports from 6881 to 6999, im not sure if its true but i heard it on a website. please help!!

You can try any ports within the range they specified... make sure in/out ports are the same and tcp is enabled....then allow the app inside your firewall

as i said before 6881 still works just fine for me

born2gain · Post by **born2gain** » Tue Mar 14, 2006 6:53 am

hi, i'm a new comer in this board, i also having trouble getting connection from bitcomet and azerues (sp), I have done my port forwarding and nothing is changed, even when i use ares, i can only get a few results from my searches.

My connection is 384k/64k and im using Prolink Hurricane 9000G Router, so if anyone here who can lend a hand then that would be much appreciate it. Thanks!!!

SG Broadband Community

" Nat error "Azureus (no firewall and no share internet connection)

with wireless?

Just want to torrent

router