This access point can act as a DHCP client. It supports Multiple SSIDs and uses WEP and WPA/WPA2 wireless encryption. It uses WMM (QoS) to prioritize the traffic over the network.
The WNDAP330 can be easily configured via Web-based configuration utility, including a Quick Setup Wizard or via SNMP v.1/ v.2.
| WNDAP330 Features | |
| General | |
| Availability: | discontinued |
| List price: | $329 |
| Street price: |
$270 |
| LAN / WAN Connectivity | |
| WAN ports: |
0 |
| LAN ports: | 1 |
| LAN ports type: | Gigabit Ethernet (RJ-45) |
| LAN ports auto cross-over: |
 |
| Serial port: |
|
| Router | |
| DHCP client: |
|
| QoS: |
|
| Routing Protocols: | VLAN tagging (802.1q) |
| Wireless | |
| Maximum Wireless Speed: | 300 Mbps (Wi-Fi 4) |
| WiFi standards supported: |
802.11b (Wi-Fi 1) 802.11a (Wi-Fi 2) 802.11g (Wi-Fi 3) 802.11n (draft 2.0) |
| Wifi security/authentication: |
WEP WPA (TKIP) WPA2 (AES) 802.1X (EAP-MD5/TLS/TTLS/PEAP) Wireless MAC Address filtering |
| WiFi modes: |
Access point Wireless bridge (PtP) Multipoint bridge (PtMP) Repeater mode |
| external antenna(s): | 3 |
| Antenna connector: | RP-SMA (Reverse SMA) |
| Multiple SSID: |
|
| WDS compatible: |
|
| WMM (QoS): |
|
| Dual Band (2.4GHz/5GHz): |
|
| VPN | |
| IPSec | |
| IPSec passthrough: |
|
| PPTP | |
| PPTP passthrough: |
|
| Device Management | |
| Default IP address: | 192.168.0.235 |
| Default admin username: | admin |
| Default admin password: | password |
| Administration: |
Web-based (LAN) Remote configuration (WAN) Quick Setup Wizard Telnet / CLI SSH SSL secure web |
| Firmware upgradeable: |
|
| Configuration backup/restore: |
|
| Event log: |
|
| Usage Statistics: |
|
| Misc hardware info | |
| Max clients: |
64 |
| SNMP support: | SNMP v.1, SNMP v.2 |
| NTP client: |
|
| Power over Ethernet (PoE): |
|
| Links | |
| Product page: | http://support.netgear.com/product/WNDAP... |
| Datasheet: | http://www.downloads.netgear.com/files/G... |
| Manual: | ftp://downloads.netgear.com/files/WNDAP3... |
| Quick Install Guide: | ftp://downloads.netgear.com/files/WNDAP3... |
Please use the Add Comment function below to review devices you have used (please be descriptive).
If you find an error in our database, or have additional information about the product,
please
|
User Reviews/Comments:
rate:
avg:
by
anonymous - 2010-06-30 12:12
You said, 10/100 - It's actually gigabit:
One (1) 10/100/1000BASE-T Gigabit Ethernet (RJ-45) port with Auto Uplink™ (Auto MDI-X) with IEEE 802.3af Power over Ethernet (PoE) support and I'm almost certain it's not Dual SSID?
Thanks for the port speed correction.
As for the multiple SSID support, the manual states: The multiple BSSID feature allows you to configure up to 8 SSIDs per Radio mode on your access point and assign different configuration settings to each SSID. All the configured SSIDs are active and the network devices can connect to the access point by using any of these SSIDs.
Thank-you so much... I have had these products for approximately 8 months, and I have had alot of trouble with them... Do you know of anyone/where that has some optimum setup configs available? I have them about 20m (65ft) away from each other, I have mine in the ceiling, and the only thing that is blocking it from it's pair is one wall (weatherboard) on my side and a window on theres... as we speak it just dropped out... I cant seen to transfer information over these faster than about 100kb/s, whereas theoretically at this distance i should be getting atleast 8MB/s...
I have done what is stated in the Netgear documents, and I've been trying to find someone else with these devices to help me configure them properly.. Nothing I have done has worked... Dropping out every 10 mins, and terrible speeds over the 802.11gn 2.4GHz bridge... |
|
|